Part 29

BAR WITH PICOT MADE IN BULLION STITCH (fig. 700).—Put the needle halfway into the last button-hole stitch, twist the thread ten or twelve times round it from left to right, draw it through and tighten the thread, so that the spiral on the thread form a semicircle, then continue the bar (see also for the bullion stitch figs. 179 and 661).

BAR WITH BUTTON-HOLE PICOT (fig. 701).—Cover rather more than half the bar with button-hole stitches, carry the thread three times to the 6th stitch and back, then button-hole these threads that are attached to the bar in the same way as the bar itself and finish the bar in the usual way.

These button-hole picots are generally used for edging lace; they may in their turn be adorned with small pinned picots to produce a richer effect.

[Illustration: FIG. 700. BAR WITH PICOT MADE IN BULLION STITCH.]

[Illustration: FIG. 701. BAR WITH BUTTON-HOLE PICOT.]

[Illustration: FIG. 702. BAR WITH TWO ROWS OF KNOTS.]

BAR WITH TWO ROWS OF KNOTS (fig. 702).—Over two foundation threads, make double knots, far enough apart to leave room for the knots of the next row between.

These double knots consist, in the first place, of one plain button-hole stitch and then one reversed, that is, made by bringing the needle out in front of the thread and passing it under the loop; the result being that the thread will lie behind the thread and not before it, as in an ordinary button-hole stitch.

[Illustration: FIG. 703. BRANCHED BARS.]

BRANCHED BARS (fig. 703).—Where you have a larger surface to cover with bars, you are generally obliged to make them with branches. For this purpose you prepare the threads as for an ordinary bar and cover them halfway with button-hole stitches; then you carry on the foundation thread to the next bar, button-hole it also halfway, lay the next foundation thread, and finally button-hole all the half-covered bars till you reach the dotted line, from whence you lay the last foundation threads.

The last bar is worked over 2 or 4 threads, so that the working thread can be taken back to the edge of the braid by means of the last button-hole stitches.

[Illustration: FIG. 704. PLAIN RUSSIAN STITCH.]

PLAIN RUSSIAN STITCH (fig. 704).—Stitches of all kinds can be used, as well as bars, for joining braids together that run parallel to each other, and for filling up the spaces between. These stitches, which serve as an insertion, are some of them very elementary, whilst others require great skill and patience to execute.

The simplest of all is the Russian stitch, which bears a great resemblance to the crossed stitch, shown in fig. 39, and the crossed back-stitch, fig. 176.

You pass the needle from left to right, under the edge of the braid, then again from right to left under the opposite edge, taking care always to leave the thread in front of the needle.

[Illustration: FIG. 705. TWISTED RUSSIAN STITCH.]

TWISTED RUSSIAN STITCH (fig. 705).—Instead of passing the needle behind the thread, pass it before it and round it, so that the needle always comes out again beneath the thread, which will then be twice twisted.

[Illustration: FIG. 706. COLUMN STITCH.]

COLUMN STITCH (fig. 706).—At the bottom, the stitch is made like the plain Russian stitch, and at the top, like the one in fig. 705, with the difference that the second thread is passed three times round the first.

[Illustration: FIG. 707. INSERTION OF SINGLE BUTTON-HOLE STITCHES.]

[Illustration: FIG. 708. INSERTION OF PLAIN BUTTON-HOLE STITCHES.]

INSERTION OF SINGLE BUTTON-HOLE STITCHES (figs. 707 and 708).—Make very loose button-hole stitches along both edges of the braid, all the same size and the same distance apart, and vertically, opposite to each other.

When these two rows are finished, pick up each loop with Russian stitch, either single, fig. 704, or twisted, fig. 705. Fig. 708 shows the double Russian stitch made in each loop; it may be trebled or quadrupled, according to whether you wish your insertion to be very transparent or not.

[Illustration: FIG. 709. INSERTION WITH BEAD STITCHES.]

INSERTION WITH BEAD STITCHES (fig. 709).—Join the opposite rows of loops together by four stitches. The threads of these stitches must lie quite flat, side by side, and not one on the top of the other. After the fourth stitch, you wind the thread round the bottom loop and then carry it on to the next, whence you repeat the four stitches as above.

CLUSTER INSERTION (fig. 710).—Over the middle of two finished plain bars and one half-finished one, a short distance apart, you make five button-hole stitches and overcast the remainder of the third bar. The first bar of the next cluster must be set quite close to the last.

INSERTION WITH BRANCHES (figs. 711 and 712).—Throw the thread across the middle of the space between two edges of braid, and lengthways, from one end to the other, pass the needle horizontally under four or five threads of the braid, across the insertion; then carry it in a similar manner, first to the left and then to the right, take up the same number of threads of the braid and connect the three loops together by a knot, as is clearly shown in fig. 711.

[Illustration: FIG. 710. CLUSTER INSERTION.]

[Illustration: FIG. 711. INSERTION WITH PLAIN BRANCHES.]

[Illustration: FIG. 712. INSERTION WITH BRANCHES AND WHEELS.]

Fig. 712 represents a similar beginning, and a similar interlacing of the threads, but ornamented this time with a wheel, added after the knot has been made over the loops.

[Illustration: FIG. 713. INSERTION WITH LEAVES WORKED IN DARNING STITCH.]

INSERTION WITH LEAVES IN DARNING STITCH (fig. 713).—Fasten on the thread where, according to the illustration, the first leaf in the insertion ought to come, carry it across to the opposite side, draw it through the edge of the braid and bring it back to the point whence it started, lay threads across to both sides, like in figs. 711 and 712, unite them by a knot, such as described in fig. 711, lay the thread once more round the middle leaf, and finish the leaf in darning stitch, working downwards from the top, as described in the preceding chapter in figs. 646 and 647. As may be seen from the second middle leaf, your darning stitches have to be made over five threads, subdivided into two and three.

[Illustration: Fig. 714. INSERTION WITH SMALL WHEELS.]

INSERTION WITH SMALL WHEELS (fig. 714).—Here, you have to make two rows of Russian stitches opposite each other and carry the thread to the point of intersection, then, you make a wheel over five threads and pass the needle under the completed wheel to reach the next point of intersection. Half wheels may also be added at the edge of the braid, as in figs. 658 and 659.

[Illustration: Fig. 715. INSERTION WITH BIG WHEELS.]

INSERTION WITH BIG WHEELS (fig. 715).—Carry the thread horizontally across the middle of the space intended for the insertion, to the opposite side, and then conduct it by means of overcasting stitches into the corner; thence make a loose loop over to the opposite corner, pass the needle under six or eight threads of the braid edge, slip it under the horizontal thread first laid and behind the loop, and finish the stitch on the other side in the edge of the braid.

Throw the thread again across the empty space and over the first thread, bring your needle back to the middle, make a big wheel over four threads, passing each time under the same threads, then overcast the single thread, come back to the edge of the braid and make the second loop, bringing out the thread at the same place where the other stitches came out.

INSERTION WITH CONES (figs. 716 and 717).—Over plain but very distended Russian stitch, make darning stitches backwards and forwards, beginning at the point and reaching to the middle, so as to form small cone-shaped figures.

To reach the point of the next cone you overcast the thread of the Russian stitch several times.

You may also, as in fig. 717, double the Russian stitch and make the darning stitches in such a manner that the points of the cones touch each other and their bases meet the edge of the braid. The same thing, worked the reverse way, that is, with the points turned outwards to the edge, produces a not less pretty effect.

[Illustration: Fig. 716. INSERTION WITH CONES.]

[Illustration: Fig. 717. INSERTION WITH CONES.]

[Illustration: Fig. 718. INSERTION WITH EMBROIDERED SQUARES.]

INSERTION WITH EMBROIDERED SQUARES (fig. 718).—After making rows of loose button-hole stitches along the braid edges, as in figs. 707, 708, 709, run a thread through the button-hole stitches; this thread serves as the foundation to the Russian stitches by which the two edges are joined together. The empty square space left between the Russian stitches is then filled up with button-hole stitches, like those in fig. 651, in the foregoing chapter.

[Illustration: Fig. 719. INSERTION WITH HALF BARS.]

INSERTION WITH HALF BARS (fig. 719).—Fasten on the thread in one of the corners of the braid and conduct it by means of overcasting stitches to the middle of the insertion, draw it through the edge of the braid on the right and make button-hole stitches over it, to the middle of the space to be filled, then carry the thread to the left, draw it through the left edge, a little higher up than on the other side, and make the same number of stitches over it as over the first. You can vary this insertion with very good result by making more stitches on one side than on the other, but it should never be more than 10 or 12 stitches wide.

[Illustration: FIG. 720. PLAIN NET STITCH. FIRST LACE STITCH.]

PLAIN NET STITCH. FIRST LACE STITCH (fig. 720).—Make rows of button-hole stitches to and fro, loose enough to form loops into which the stitches of each subsequent row are set. You must be careful to make the same number of stitches in all the spaces that are of the same size, and also, when you begin a row with a whole stitch, to begin the return row with a half, and so on, in regular rotation.

The number of stitches should vary with the width of the pattern and the decreasing and increasing should always be done at the edge.

The loops must be as many threads of the braid edge long, as they are wide.

[Illustration: FIG. 721. DOUBLE NET STITCH. SECOND LACE STITCH.]

DOUBLE NET STITCH. SECOND LACE STITCH (fig. 721).—You leave the same distance between the stitches here as in the preceding figure, but in each of the loops of the first row, you must make two button-hole stitches close together. It is as well to round the loop a little less than is usually done in net stitch.

[Illustration: FIG. 722. THIRD LACE STITCH.]

THIRD LACE STITCH (fig. 722).—Here, you make three button-hole stitches close together, joined to the next three by a loop of thread, just long enough to hold the three button-hole stitches of the subsequent row.

[Illustration: FIG. 723. FOURTH LACE STITCH.]

FOURTH LACE STITCH (fig. 723).—Working from left to right, make two button-hole stitches rather near together, and leave twice as long a loop between them and the next two stitches as between the two first.

In the next row, which is worked from right to left, make one stitch in the loop between the two stitches that are close together and three or four in the long loop.

[Illustration: FIG. 724. FIFTH LACE STITCH.]

FIFTH LACE STITCH (fig. 724).—As in fig. 723, you begin this stitch from left to right, but making three stitches very close together with an intermediate loop as long as the three stitches in one.

In the second row, you make one button-hole stitch in each of the loops between the three stitches and six or eight in the long intermediate loop.

[Illustration: FIG. 725. SIXTH LACE STITCH.]

SIXTH LACE STITCH (fig. 725).—Over wide loops, made from left to right in the first row, make in the second, enough button-hole stitches entirely to cover the thread.

In the third row of stitches, put the needle into the small loop between two sets of button-hole stitches, so that the close stitches shall form vertical lines across the surface they cover.

This stitch admits of every sort of modification, such as, for instance, making the third row of stitches on the button-hole stitches, in the middle of the ones on the small loop; or making one row of close stitches first, and then three open rows; in the former case you should always make an uneven number of button-hole stitches, so that you have the same number on both sides of the needle, which you must put in between the two threads that form the middle button-hole stitch.

[Illustration: FIG. 726. SEVENTH LACE STITCH.]

SEVENTH LACE STITCH (fig. 726).—Begin, working from right to left, by making one row of pairs of button-hole stitches, a very short distance apart; in the second row you make one button-hole stitch between each of these pairs, and in the third row, two button-hole stitches in every long loop. Here, the stitches must not be crowded together but have a small gap left between them.

[Illustration: FIG. 727. EIGHTH LACE STITCH.]

EIGHTH LACE STITCH (fig. 727).—This stitch is generally known as the “pea-stitch” on account of the holes occasioned by the different distribution of the stitches.

The first row consists of stitches, set rather closely together, and all the same distance apart. In the second row, you make one button-hole stitch in the last stitch of the first row, then, missing two loops and three button-hole stitches, you make two stitches in the next loops and so on. In the third row, you make three stitches in the big loop, and one in the loop between the stitches of the second row.

[Illustration: FIG. 728. NINTH LACE STITCH.]

[Illustration: FIG. 729. TENTH LACE STITCH.]

NINTH, AND TENTH LACE STITCH (figs. 728 and 729).—Both, the small and the big pointed groups of stitches, begin with a row of close button-hole stitches.

Fig. 728 requires three rows; in the second you miss two stitches and make two in the next loops; in the third, only one stitch is introduced between the two loops of the lower row.

Fig. 729 requires five rows. The stitches of the first must be set as closely together as possible; in the second row you make four stitches and miss two of the first row, in the third row you make three stitches, in the fourth, two and in the fifth, one only. The long loops of the last row must not be too slack so that the first stitches of the next scallop may quite cover them.

[Illustration: FIG. 730. ELEVENTH LACE STITCH.]

ELEVENTH LACE STITCH (fig. 730).—This stitch is not really more difficult to work than those we have been describing, but requires rather more attention to learn.

The first row consists of plain net stitches; in the second, you have three button-hole stitches in the middle net stitch; in the third, three button-hole stitches in the whole loops on either side of the three button-hole stitches of the second row, and one stitch in the half loops that precede and immediately follow them; the fourth row is similar to the second.

In the fifth row the close stitches are changed. The three button-hole stitches are made in the third whole loop, before and after those of the fourth row, so that between two groups of three stitches you have six single button-hole stitches and seven loops.

[Illustration: FIG. 731. TWELFTH LACE STITCH.]

TWELFTH LACE STITCH (fig. 731).—Fasten on your thread, take it by overcasting stitches over the braid edge, half a c/m. from the corner, and make three button-hole stitches downwards, quite close together. The next loops, over four or six threads of the braid, must be left long enough to be on a level with the first stitch reaching downwards from the edge.

In the second row, you cover the long loops with three button-hole stitches and draw the intervening thread quite tight.

The third row is like the first, with the difference, that you put the needle in between the two threads of the button-hole stitch, instead of through the loops.

[Illustration: FIG. 732. THIRTEENTH LACE STITCH.]

THIRTEENTH LACE STITCH (fig. 732).—The stitch here represented, as well as the two next ones are looped from left to right and then again from right to left.

As it is more unusual to make the loops from left to right than the reverse way, the proper position of the needle and the course of the thread are shown in the illustrations.

Fig. 732 requires, in the first place, two button-hole stitches very close together in the edge of the braid, then a third stitch covering the two first stitches and set quite close to them; the connecting thread between these stitches must be tightly stretched so as to lie almost vertically, that the stitches may form straight lines.

[Illustration: FIG. 733. FOURTEENTH LACE STITCH.]

FOURTEENTH LACE STITCH (fig. 733).—This begins, likewise, with two button-hole stitches, above which you make two button-hole stitches instead of one, as in fig. 732, producing an open ground with vertical bars.

[Illustration: FIG. 734. FIFTEENTH LACE STITCH.]

FIFTEENTH LACE STITCH (fig. 734).—This resembles the two foregoing stitches and consists of three button-hole stitches, made over the edge of the braid or the intermediate bars, and joined together afterwards under one transverse stitch.

[Illustration: FIG. 735. SIXTEENTH LACE STITCH.]

SIXTEENTH LACE STITCH (fig. 735).—You begin this by a row of net stitches worked from right to left, or as the engraving shows, by a row of stitches called «seed stitches».

[Illustration: FIG. 736. SEVENTEENTH LACE STITCH.]

The second row, worked from left to right, consists of short bars, set slanting and shaped like a seed, and made the same way as the picot in fig. 699. The first stitch is carried through the loop of the row below, the second over both threads and far enough from the loop to leave room for three other stitches. The first of the four button-hole stitches of the next group must be set quite close to the last.

SEVENTEENTH LACE STITCH (fig. 786).—Here we have the same pattern as the preceding one without the row of net stitches; the engraving shows us at the same time, the proper direction of the needle and thread for the row that is worked from right to left.

[Illustration: FIG. 737. EIGHTEENTH LACE STITCH.]

EIGHTEENTH LACE STITCH (fig. 737).—This is the first of a series of lace stitches, often met with in old Venetian lace, and which can therefore with perfect right be called, Venetian stitches.

Owing to the manner and order in which the rows of stitches are connected and placed above one another, they form less transparent grounds than those we have hitherto described.

In these grounds you begin by making the row of loops, then you throw a thread across on the same level and in coming back, pass the needle through the row of loops under the thread stretched across, and under the stitch of the previous row.

[Illustration: FIG. 738. NINETEENTH LACE STITCH.]

NINETEENTH LACE STITCH (fig. 738).—The close stitch here represented is more common in Venetian lace than the loose stitch given in fig. 737.

[Illustration: FIG. 739. TWENTIETH LACE STITCH.]

TWENTIETH LACE STITCH (fig. 739).—By missing some loops of the close ground in one row and replacing them by the same number in the next, small gaps are formed, and by a regular and systematic missing and taking up of stitches, in this way, extremely pretty grounds can be produced.

[Illustration: FIG. 740. TWENTY-FIRST LACE STITCH.]

TWENTY-FIRST LACE STITCH (fig. 740).—These close lace stitches, can be varied in all sorts of other ways by embroidering the needle-made grounds.

In fig. 740, you have little tufts in darning stitch, and in a less twisted material than the close stitches of the ground, worked upon the ground.

If you use Fil à dentelle D.M.C (lace thread) for the ground, you should take either Coton à repriser D.M.C (darning cotton), or better still, Coton surfin D.M.C[A] for the tufts. The ground can also be ornamented with little rings of button-holing, stars or flowerets in bullion or some other fancy stitch.

[Illustration: FIG. 741. TWENTY-SECOND LACE STITCH.]

TWENTY-SECOND LACE STITCH (fig. 741).—For the above three stitches and the three that follow, the work has to be held, so that the finished rows are turned to the worker and the needle points to the outside of the hand. In the first row, from left to right, take hold of the thread near the end that is in the braid, lay it from left to right under the point of the needle, and bring it back again to the right, over the same. Whilst twisting the thread in this way round the needle with the right hand, you must hold the eye of the needle under the left thumb.

When you have laid the thread round draw the needle through the loops; the bars must stand straight and be of uniform length. Were they to slant or be at all uneven, we should consider the work badly done.

In the row that is worked from left to right, the thread must be twisted round the needle, likewise from left to right.

[Illustration: FIG. 742. TWENTY-THIRD LACE STITCH.]

TWENTY-THIRD LACE STITCH (fig. 742).—This is begun with the same stitches as fig. 741, worked from right to left. You then take up every loop that comes between the vertical bars with an overcasting stitch, drawing the thread quite out, and tightening it as much as is necessary after each stitch. You cannot take several stitches on the needle at the same time and draw out the thread for them all at once, as this pulls the bars out of their place.

[Illustration: FIG. 743. TWENTY-FOURTH LACE STITCH]

TWENTY-FOURTH LACE STITCH (fig. 743).—This is often called the Sorrento stitch.

Every group of three bars of stitches is separated from the next by a long loop, round which the thread is twisted in its backward course. In each of the succeeding rows you place the first bar between the first and second of the preceding row, and the third one in the long loop, so that the pattern advances, as it were in steps.

[Illustration: FIG. 744. TWENTY-FIFTH LACE STITCH.]

[Illustration: FIG. 745. TWENTY-SIXTH LACE STITCH.]

TWENTY-FIFTH AND TWENTY-SIXTH LACE STITCHES (figs. 744 and 745).—These two figures show how the relative position of the groups of bars may be varied.

Both consist of the same stitches as those described in fig. 741. The thread that connects the groups should be tightly stretched, so that the rows may form straight horizontal lines.

[Illustration: FIG. 746. TWENTY-SEVENTH LACE STITCH.]

TWENTY-SEVENTH LACE STITCH (fig. 746).—Begin by making two rows of net stitches, fig. 720, then two of close ones, fig. 738, and one row like those of fig. 741.

If you want to lengthen the bars, twist the thread once or twice more round the needle. You can also make one row of bars surmounted by wheels, as shown in fig. 765, then one more row of bars and continue with close stitches.

TWENTY-EIGHTH LACE STITCH (fig. 747).—Between every group of three bars, set close together, leave a space of a corresponding width; then bring the thread back over the bars, as in figs. 737, 738 and 739, without going through the loops. In the second row, you make three bars in the empty space, two over the three bars of the first row and again three in the next empty space. The third row is like the first.