CHAPTER I
=KITCHEN CONVENIENCES=
VEGETABLE PARING TABLE
A convenient kitchen table made of poplar and covered with zinc with an opening in the center through which the parings of vegetables or the scraping of dishes may be put into a pail sitting on the lower shelf. This saves soiling the floor and many steps while preparing the vegetables for cooking. It should be remembered that the pail underneath must be removed and the contents emptied into the garbage barrel after each using. It is not a garbage pail and should in no sense be used as such. Above the table hooks on which hang many smaller cooking utensils, such as paring knives, graters, spoons, scissors, or can openers, are all arranged to accommodate the housekeeper.
MATERIALS:
12’ poplar. ¼ lb. 6-penny nails to construct table. 1 piece of sheet zinc, 12” × 30”, to cover the top of table.
DIMENSIONS:
_Top_: 1 piece 1” thick × 18” wide × 26” long. _Shelf_: 1 piece 1” thick × 10” wide × 32” long. _Legs_: 4 pieces 1½” thick × 1½” wide × 24” long. _Cleats_: 4 pieces 1” thick × 1” wide × 14” long.
DIRECTIONS:
After cutting legs, nail on cleats even with the top edge, measuring 14” for the bottom cleat. Measure 2” from the ends and sides of the top and nail on the legs. Measure 7¾” from the right-hand end and 9” from the side and make a hole 8” in diameter. Nail the bottom shelf at an equal distance from the bottom of the legs.
[Illustration]
WALL CABINET FOR THE KITCHEN
(MADE FROM DRY GOODS BOXES)
A comfort to the housewife is a kitchen cabinet, containing different compartments for spices and such accessories necessary in cooking. It is made of boxes and should be put at some place convenient to the work table so the woman will not have to move to get these things when preparing a meal. It surely fulfils the old adage, “A place for everything and everything in its place.”
MATERIALS:
1 box of the required dimensions to build the body. 12 salt boxes used as drawers in the compartments. ⅓ lb. 8-penny nails to be used in the construction of the cabinet. 12 round-head screws to be used as knobs. Sandpaper and stain.
DIMENSIONS:
_Body_: 1 box 4¾” deep × 13¼” wide × 18¼” long. _Shelves_: 4 pieces ⅜” thick × 4¾” wide × 12¼” long. _Drawers_: 12 salt boxes, 4” × 4” × 4”.
[Illustration]
[Illustration]
DIRECTIONS:
Remove the sides from the box, making them the exact length of the inside of the box. Draw a line across the bottom and the ends of the box about 2” from the edge of the sides. Nail the sides to the bottom and the ends of the box about 2” from the edge of the sides, with outside faces on pencil line. Plane and sandpaper the edges until they are smooth. Nail the shelves in at equal distances apart to make four compartments of equal size. Place three of the salt boxes in each compartment. Sandpaper, stain, and polish.
IRONING BOARD
This ironing board is a very great step saver. It is always ready and in place. It is fastened to the wall at the most convenient place and adjusted to suit the one who is to use it. When not in use it can be folded up and hinged against the wall out of the way. The leg is hinged to the ironing board and falls into position when the board is lifted. Skirts may be easily ironed without changing the position of the leg.
MATERIALS:
8’ of pine. 3 3” plain steel (butt) hinges. 2½ doz. 1½” No. 12 flat-head screws. 2 yds. of white cotton flannel. 2½ yds. unbleached muslin. 2 pieces of cotton tape.
DIMENSIONS:
1 piece 1” thick × 14” wide × 3’ long to be used as top of board. 1 piece 1” thick × 4” wide × 10” long to be used as a board strip. 2 pieces 1” thick × 2” wide × 4” long to be fastened to the wall to hold the board in position. 1 piece 1” thick × 4” wide × 14” long to be used as a wall strip. 1 piece 1” thick × 4” wide × 4’ long to be used as brace for board. 1 piece 1” thick × 4” wide × 8” long to be used as brace support.
DIRECTIONS:
Plane the top of the board (1” × 14” × 3’) on the smoothest side. With a radius of 4½” lay out a semi-circle at the middle of one end of the board as shown in illustration. This may be done with a compass or with a string and pencil. Make the other end of the board square with one edge. Two feet from each end make a mark on each edge and draw a straight line from each of these marks tangent to the semi-circle. Saw along these lines, smoothing the edges with the plane. Fasten the wall strip (1” × 4” × 14”) to this top with 2 No. 3 (butt) hinges. Bore 3 ¼” holes through the board strip (1” × 4” × 10”) and fasten it to the bottom of the top at a distance of 34” from the wall strip. The brace (1” × 4” × 4’) is fastened to the board strip with one No. 3 (butt) hinge. ¾” holes are bored through the wall strip and it is fastened at a convenient height to the wall with 3 flat-head screws. After boring 3 ½” holes through the brace support (1” × 4” × 8”) it is screwed to the wall with 3 flat-head screws. Place this support directly below the wall strip and at such a distance from it to make the board level when the brace is in position. Bore 2 ¼” holes in one of the pieces measuring 1” × 2” × 4”, and one hole through the other piece. Fold the board up against the wall and fasten the piece with the two holes to the wall just a little to one side of the board and 2’ above the wall strip. The other piece with one hole is fastened to this piece to hold the ironing board in position.
[Illustration]
The covering may be made of cotton flannel or an old blanket. Allow 2” on the sides and the end to be turned under after it has been cut the shape of the board. This must be tacked firmly and smoothly on the board. The ironing sheet may be made of unbleached muslin or an old sheet. This is also cut the shape of the board, allowing 4” on the sides and end for the hem. Attach pieces of tape to the opposite sides about 10” apart to tie the sheet on the board.
JELLY STRAINER NO. 1
An old chair is generally used to hang the jelly bag over while the juice is dripping. As a substitute the device shown in the following illustration is suggested as being more convenient and sanitary in every way. It not only provides a place for the bag to hang, but it also has a shelf on which the pan sits to catch the drippings from the bag. The legs are adjustable; hence it is easily taken apart and kept in a small space. This makes the strainer especially convenient to the Canning Club Agent as she goes her daily rounds teaching the housekeepers the art of jelly-making. It can be easily made at home and at a little cost.
MATERIALS:
3’ poplar. 12 No. 10 screws, 2¼”, to fasten the adjustable legs to the shelves. 8 No. 9 screws, 1”, to fasten braces to the top of strainer, 1 yd. white flannel for the jelly bag. 1 piece of white tape to make loops on bag.
[Illustration]
[Illustration]
DIMENSIONS:
_Legs_: 4 pieces 1½” thick × 1½” wide × 31½” long. _Shelves_: 4 pieces 1” thick × 1½” wide × 7” long to make the upper shelf. 1 piece 1” thick × 15” wide × 15” long for lower shelf. _Braces_: 4 pieces 1” thick × 2½” wide × 3” long to be cut into 4 equal triangles.
DIRECTIONS:
Bevel the tops of all 4 of the legs at an angle of 45°. Make the upper shelf of the 4 pieces measuring 1” × 1½” × 7”. Measure 2¼” from the tops of the 4 legs and screw the upper shelf to the legs at these points. A solid piece of wood with a hole in the center may be used in making this shelf. Support this upper shelf by screwing the four triangular braces (1” × 2½” × 3”) in the corners of the shelf. Use the 8 1-inch No. 9 screws for this purpose. Saw the lower shelf out 1½” on each corner and screw it on the legs at a distance of 9” from the bottom of the legs. Sandpaper but do not stain. Take a piece of flannel of the desired size and make the jelly bag in the shape of a triangle. Sew a loop of tape at each corner to hang the bag over the posts.
JELLY STRAINER, NO. 2
While this jelly strainer is unique and useful in its construction it is not adjustable. It is made of poplar at a minimum cost. Around the top edge are arranged little brass hooks. These are put at equal distances apart. At the lower end of the trough two plugs are put, one above the other, through which the jelly juice flows out into a pan placed beneath the plugs.
[Illustration]
The jelly bag is made of an oblong piece of flannel with ivory rings sewed around the edges so as to hang the bag on the brass hooks around the top of the frame.
MATERIALS:
4’ of poplar. 4 No. 9 screws, 1½”, to fasten handles on the sides. 16 No. 10 screws, 2”, to fasten ends on the sides. 5 No. 10 screws, 1¼”, to fasten the sides together at the bottom. 14 brass cup hooks arranged around the top edges. 14 white ivory rings to be sewed on jelly bag. 1 yd. white flannel for jelly bag.
DIMENSIONS:
_Sides_: 2 pieces 1” thick × 12” wide × 15½” long. _Ends_: 2 pieces 1” thick × 12½” wide × 17½” long. _Handles_: 2 pieces 1” thick × 2½” wide × 4” long. _Plugs_: 2 pieces 1” thick × 1” wide × 3” long.
DIRECTIONS:
Saw the two end pieces according to the illustration. Measure 6½” from the bottom of each end and cut them out ¼” to fit sides (1” thick) placing the sides ¾” from the outer side of the end pieces. Measure equal spaces from each side of the ends and put the handles 1½” from the top edge. Bore two holes ¾” in diameter near the bottom of the end to fit the plugs. Bevel the two sides (1” × 12” × 15½”) at the bottom so as to make a tight and neat joint. Screw the end pieces to the sides. Screw the brass cup hooks at equal distances apart around the top edge of the strainer.
[Illustration]
DISH DRAINER
The work of dish-washing is greatly reduced by the use of a dish drainer. The dishes are carefully washed and arranged in the drainer, and boiling water poured over them. When they are dry, they can be put away or allowed to stand with a clean cloth thrown over them until ready to use.
This dish drainer resembles a box in shape, put on legs, with slats placed inside at equal distances apart, making the compartments to hold the dishes. The space in front is made a little larger to accommodate the irregular dishes. An experienced housewife will know that glassware and silverware cannot be dried by this method. A hole is made in one corner of the drainer through which the water drains off into a pail which is kept under the corner.
MATERIALS:
16’ of white pine. ½ lb. of 4-penny nails for nailing slats in box. ½ lb. of 8-penny nails for nailing box on the legs. 4½’ of sheet zinc to cover the inside of drainer. 4” of half-galvanized pipe for drainage tube. 1 drainage pail. Sandpaper. 1 can of white paint. 1 can of white enamel.
DIMENSIONS:
_Bottom_: 1 piece 1” thick × 24” wide × 26” long. _Sides_: 2 pieces 1” thick × 8” wide × 26” long. 2 pieces 1” thick × 8” wide × 24” long. _Legs_: 4 pieces 1” thick × 4” wide × 36” long, for back legs. 4 pieces 1” thick × 4” wide × 35” long, for front legs. _Slats_: 2 pieces ¼” thick × 1” wide × 24” long. 6 pieces ¼” thick × 1” wide × 26” long.
DIRECTIONS:
Make a pine box which is 8” deep and 24” × 26” long. The joints must be laid in white lead in order to make the drainer water tight. Nail 2 slats ¼” thick × 1” wide × 24” long down flat from the front to the back of the box at the outer edge. These are used as supports for the other crosswise slats and also allow the water to run under the slats. Nail 4 slats on these supports, beginning 3¼” from the back of the box and making a distance of 3¼” between each slat. This will leave a 9” space in front of the box for the irregular dishes. The front legs are made of the four pieces 1” thick × 4” wide × 35” long, and the back legs are 1” thick × 4” wide × 36” deep. This slant provides for the drainage. The drainer should be tipped a little to the corner in which the drain pipe is placed. If zinc is to be used for lining, it must be done before the slats are put into the box.
[Illustration]
DISH RACK
A rack made of poplar, with several compartments to accommodate dishes of different sizes.
The large platters are put in the largest upright spaces, the dinner plates being arranged in the middle-sized spaces, with the smaller plates and saucers in the top spaces. It may be placed at a convenient place in the kitchen or dining room so as to save the housekeeper unnecessary steps. Mortise and tenon joints will make a more substantial rack but these are not necessary. The parts may be nailed together. After joining the parts together, sandpaper, paint white and enamel.
MATERIALS:
6½” poplar. 12 No. 6 nails to nail on the top. 45 No. 44 box nails for nailing on upright pieces. 50 No. 16 wire brads, ¾”, for nailing tenons in mortise. 2 No. 9 screws, 1½”, to screw the base on the rack. Sandpaper for dressing the rack. 1 pt. white paint. 1 pt. enamel.
DIMENSIONS:
_Top_: 1 piece ¾” thick × 4½” wide × 33” long. 2 pieces ¾” thick × 1½” wide × 30” long. _Bottom_: 2 pieces ¾” thick × 1½” wide × 30” long. 1 piece 1” thick × 2½” wide × 12” long for base. _Middle_: 2 pieces ¾” thick × 1½” wide × 21” long. _Ends_: 2 pieces ¾” thick × 1½” wide × 24” long. _Crosspieces_: 2 pieces ¾” thick × 1½” wide × 3” long to be used as top of rack. 2 pieces ¾” thick × 3” wide × 3” long to be used as bottom of rack. _Upright pieces_: 16 pieces ½” thick × ½” wide × 26” long to be used as side pieces 8 on each side. 2 pieces ¾” thick × 1½” wide × 20½” long.
[Illustration: _Dish Rack_]
DIRECTIONS:
Mortise the two end pieces ¼”, to fit tenon. Nail the two crosspieces, measuring (¾” × 1½” × 3”) to them. Make ¼” mortises on the two top pieces (¾” × 3” × 3”). These mortises are made 3” from the end and the two pieces nailed to crosspieces. Screw on the bottom board (1” × 2½” × 12”) with 1½” No. 9 screws. Mortise the 4 top and bottom pieces (¾” × 1½” × 30”) ½” from the top and bottom and nail them lengthwise on the rack. The two middle pieces (¾” × 1½” × 21”) are mortised and nailed 11” from the top edge of the bottom piece. The upright pieces (¾” × 1½” × 20½”) are nailed 9” from the left side. Nail the eight upright pieces (½” × ½” × 26”) on each side with No. 4 box nails. The top piece (¾” × 4½” × 33”) is nailed on the top of the rack. Sandpaper, paint and enamel.
[Illustration]
COAL BOX
The construction of this box is both simple and convenient, and it requires little space in the room to accommodate it. There are four compartments in it. The back is divided equally to provide places for the kindling and paper; the front space is used for coal, and while it makes it more durable to line it with metal, this is not necessary. There is a narrow opening in the front in which the cleaning materials are kept--polish, brush, and stove rags. Stain or paint will make the coal box more attractive.
MATERIALS:
27½’ of poplar. 3 pairs of 1½” (butt) hinges. 24 ¾” No. 8 screws for hinges. 2 lbs. 5-penny box nails. 3 screen door handles. 1 iron door button. 4 castors. 5 lbs. sheet metal.
DIMENSIONS:
_Top_: 1 piece 1” thick × 1’ 9¾” wide × 2’ 1½” long to be used as level top. _Front_: 1 piece 1” thick × 1’ 7” wide × 2’ 1½” long for the slanting front. _Bottom_: 1 piece 1” thick × 1’ 11½” wide × 2’ 10” long. _Back_: 1 piece 1” thick × 2’ 1” wide × 1’ 11½” long to be used as the back of the box. _Ends_: 2 pieces 1” thick × 2’ 2” wide × 3’ long. _Partitions_: 1 piece 1” thick × 21” wide × 1’ 11½” long to be used as the partition in the back. 1 piece 1” thick × 2’ 2” wide × 1’ 11½” long to be used as the slanting partition in the bottom of the coal box. _Supports_: 1 piece ½” thick × ½” wide × 1’ 11½” long to be used as a support at the back of the opening in the box to hold door in place. _Drawer_: 1 piece 1” thick × 1’ 1½” wide × 2’ 1½” long for the front of the drawer. 1 piece 1” thick × 5” wide × 1’ 11½” long for the back of the drawer. 1 piece 1” thick × 10” wide × 1’ 11½” for the top of the drawer.
[Illustration:]
DIRECTIONS:
Measure 1’ 9¾” from the back of the two end pieces (1” × 2’ 2” × 3’). Cut the corners off from this point to make a slant which will fit the door 1’ 7” long. Nail the back (1” × 1’ 11½” × 2’ 1”) to the two end pieces at the straight edge. The bottom piece (1” × 1’ 11½” × 2’ 10”) is then nailed to the back and sides. Cut out a 4” × 1’ 11½” opening in the front piece (1” × 1’ 11½” × 2’ 1½”) for the drawer and then nail the front to the sides and bottom. Take the piece which has been cut out and hinge it to the opening as shown in the illustration. Nail the back and top partitions in this opening before the slanting partition which divides this division from the coal bin is put in. Measure 9” from the back of the coal box and put the straight partition (1” × 21” × 1’ 11½”) in by nailing it to the bottom and sides of the coal box. Then the slanting partition (1” × 2’ 2” × 1’ 11½”) is nailed to the bottom and front edge of the box as shown in the illustration. Cut an opening (9” × 1’ 11½”) in the top (1” × 1’ 9¾” × 2’ 1½”) and then nail top on the box, using the piece which is cut out for the door to the opening. Hinge this piece on with one pair of 1½” (butt) hinges. The door support (½” × ½” × 1’ 11½”) is nailed on the inside of the back of the box. Bevel the piece (1” × 1’ 7” × 2’ 1½”) for the slanting door. It must fit each edge as shown in the illustration. Hinge this door at the upper edge of the top with one pair of 1½” (butt) hinges. One screen door handle is put on each opening to lift them. The four castors are placed on the bottom of each corner of the box to make it more easily moved about. Stain or paint the coal box.
[Illustration]
A HOME-MADE COOK STOVE DRIER
This apparatus is designed to use on a wood or coal stove, an oil stove, or a gas range. It can be easily and inexpensively made at home.
MATERIALS:
12’ of poplar for the frame. 14 lbs. black sheet steel, 27 gauge, to cover frame. 9 sq. ft. galvanized wire cloth about ¼” mesh for shelves. ½ lb. 4-penny nails. 1 hook and eye to fasten door. 2 prs. small hinges for the door.
DIMENSIONS:
_Frame_: 4 pieces 1¼” × 1¼” × 23”. _Sides_: 4 pieces 1¼” × 1¼” × 21”. _Front_: 2 pieces 1¼” × 1¼” × 11”. _Back_: 2 pieces 1¼” × 1¼” × 11”. _Supports_: 6 pieces 1” × 2¼” × 23½”. _Trays_: 12 pieces ¾” × ¾” × 20½”. 12 pieces ¾” × ¾” × 10½”.
DIRECTIONS:
The frame consists of four wooden posts (1¼” × 1¼” × 23”); four side pieces (1¼” × 1¼” × 21”); two front pieces (1¼” × 1¼” × 11”); and two back pieces (1¼” × 1¼” × 11”). To the posts are lightly nailed on each side six strips (1” × 2¼” × 23½”). These pieces serve as supports for the drying racks. The corners are notched out as indicated in the drawing to allow the strips to extend out to the outer wall of the drier.
For each side use a sheet of light weight sheet steel (23½” × 23”); for the back a sheet (13½” × 23”); for the top a sheet (13½” × 23½”). In the top piece an opening about 3” × 10” is cut about four inches from the back edge to permit the escape of moist air. It may be found at times that this ventilating opening is too large. Then it may be partially closed by placing over it a tin pan or other vessel.
For the bottom a sheet 13½” × 23½” is used. This sheet is thoroughly perforated with holes to admit the warm air. Another piece of sheet steel (A on the drawing) (7½” × 17½”) is provided to make the heat spread more evenly. This piece rests on wires above the bottom of the drier. These wires are put through small holes punched in the side sheets (see B on drawing).
The door is made of heavier gauge sheet steel (13½” × 23”).
The legs are made of four pieces of sheet steel bent on an angle as indicated in the drawing.
All the sheet steel parts may be tacked on the frame but the door, which is secured by hinges.
The frames of the six trays are made of ¾” wood 10½” wide and 20½” long. Make the bottom of the trays of wire cloth (20½” × 10½”). This is tacked on the underside of the frame of the trays.
By referring to the drawing it will be observed that the bottom tray is shoved back as far as it will go; the next tray above is pulled as far front as the door will admit; the next tray is shoved back and so on with each tray shoving one to the back and pulling the other to the front. The object of this arrangement is to allow the heat to pass over and around the ends which causes a more rapid movement of the air current. This is more important in drying than the heat.
It may be necessary to shift the trays by putting the top one on the bottom and the bottom one on the top during the drying process so as to dry the products more uniformly.
[Illustration]
[Illustration: Home-made driers ready for use. (Courtesy of Peabody College for Teachers, Nashville, Tenn.)]
WOOD BOX
(MADE FROM DRY GOODS BOXES)
[Illustration]
What an unsightly spectacle does a wood pile by the stove, on the porch, or in the corner of the room present! It is a place of refuge for all trash, such as old papers and rags. This not only adds to the untidiness of the room or porch, but it makes extra work for the already overworked woman. The wood box made of old dry goods boxes should appeal strongly to the home. It can be kept by the stove or on the porch or in some convenient place to be reached, and to be filled by the man before he goes to his daily work. A lid will not only cover up the contents of the box, but it will serve as a comfortable seat to be used while preparing the meal.
MATERIALS:
1 packing box, 24” deep × 23½” wide × 32” long. 1 pair 2” (butt) hinges with ⅝” screws to fasten on top. ¼ lb. 8-penny nails to make box. Sandpaper and stain.
DIMENSIONS:
_Body_: 1 box 24” deep × 23½” wide × 32” long. _Top_: 1 piece ¾” thick × 18” wide × 32” long. _Legs_: 4 pieces ¾” thick × 2” wide × 28¾” long. 4 pieces ¾” thick × 2½” wide × 28¾” long. _Cleats_: 2 pieces ½” thick × 3” wide × 15” long. _Hinge Strip_: 1 piece ½” thick × 3” wide × 29” long.
DIRECTIONS:
Make the legs 4” longer than the depth of the box after the cover has been removed, and nail them on the box. Make the cover 2” wider and 2” longer than the outside length and width of the box. Place each cleat about 3” from the end of the cover and nail on the cover. Hinges are put 5” from each end of the box. Sandpaper, stain and polish.
[Illustration]
FIRELESS COOKER
There are many advantages in having a fireless cooker in the home. It not only saves time and fuel but keeps the woman from standing over the hot fire, and there are many foods that are better when cooked at a lower temperature. The principle of the fireless cooker is to retain the heat by boiling the food in a vessel with a tight cover and placing it in the cooker in the same vessel, thus keeping the heat from escaping. An outside container may be made to accommodate one or more cooking vessels. A cheap but efficient fireless cooker may be made of a tightly built wooden box, a barrel, or a tin lard can as shown in the illustration. If the outside container is of wood it must be lined on the inside with asbestos or heavy paper to keep out the air.
The nest may be a galvanized or tin bucket of a size which will admit of three inches of packing between the outside container and the nest. The sides and bottom of the nest are covered with asbestos to prevent the scorching or the burning of the packing.
The packing must be of some material through which the heat cannot easily escape. Cork, sawdust, excelsior, hay, or shredded newspaper may be used to an advantage. Three inches of this packing is put tightly in the bottom of the outside container and around the sides to fill in the space between the outside container and the nest.
A four-inch space is left at the top of the fireless cooker in which a cushion made of unbleached cotton or some other material is stuffed with the packing and placed to make the cooker air-tight. Cut two circles out of the unbleached cotton and a three-inch straight piece to join the circles together. A hot soapstone, stove plate or brick is placed in the bottom of the nest before the food vessel is placed in the fireless cooker. The food vessel may be any cooking utensil with a top that will fit in the nest after the soapstone has been put in. Cut a circle of tin or cardboard to fit top of inside of cooker with an opening the size of the nest. This gives a good finish to the top of the fireless cooker and preserves the packing.
[Illustration]
[Illustration: Assembled material for building a fireless cooker. 1, Outside container; 2, paper for lining; 3, material for packing; 4, inside nest; 5, cooker vessel; 6, soapstone; 7, paste; 8, tape; 9, cardboard; 10 muslin for cushion; 11, stain; 12, a finished cooker; 13, top to inside nest]
MATERIALS:
1 lard can 18” × 24”. 1 lard can 12” × 15”. 4 lbs. excelsior. 1 yd. asbestos. ¾ yd. unbleached cotton. 1 soapstone. 1 sheet cardboard.
DIMENSIONS:
_Outside Container_: 18” × 24”. _Nest_: 12” × 15”. _Cooking Vessel_: 11½” × 13”.
DIRECTIONS:
Place 3” of excelsior in the bottom of the outside container (18” × 24”) and pack it down tightly. Cover the bottom and sides of the nest (12” × 15”) with asbestos. Then place nest in the outside container holding it in place while 3” of packing is put tightly between the outside container and nest. Cut the cardboard circle to fit inside of the top of outside container with an opening to fit the top of the nest and put on top to give a good finish and to preserve the packing. Make the cushion for the top of the unbleached cotton by cutting two circles with 3” strip to join them together. Then pack the cushion tightly with the same packing. Enamel the cooker.
[Illustration]
[Illustration: Any convenient box may be used and any can of convenient size, such as a lard can, etc. The cans should be wrapped with about 4 or 5 layers of asbestos paper. The space around the cans should be at least 2 inches, and filled with straw or wood shavings, etc. The top of the cans should be covered with a pad filled with straw or shavings, etc.]